Creo Configuration Management Tool
Showing category for Creo
Yes - Enables RFS/Default gtols to be created even when not permitted by ANSI standard
Yes - If the display is in the default pan/zoom setting (View>Pan/Zoom>Reset), the system checks whether an angular dimension is visible on the screen. If it is not visible, then the system moves the dimension to a visible location
An alternative format for setting default angular tolerance dimensions. The value sets the number of decimal places, and the tolerance is the actual tolerance value. For integer dimensions, the value is zero, and the tolerance is an integer
Sets the default tolerance for angular dimensions. Each option sets a tolerance for a specific decimal place. The value is the place of the last decimal
Sets the default tolerance for angular dimensions. Each option sets a tolerance for a specific decimal place. The value is the place of the last decimal
Sets the default tolerance for angular dimensions. Each option sets a tolerance for a specific decimal place. The value is the place of the last decimal
Sets the default tolerance for angular dimensions. Each option sets a tolerance for a specific decimal place. The value is the place of the last decimal
Sets the default tolerance for angular dimensions. Each option sets a tolerance for a specific decimal place. The value is the place of the last decimal
Sets the default tolerance for angular dimensions. Each option sets a tolerance for a specific decimal place. The value is the place of the last decimal
Yes - All dimensions created will be displayed as fractions
Sets the display of newly created angular dimensions both in the model and in the drawing. There is no impact on dimensions previously created. ang_deg - Decimal degrees. ang_min - Degrees and decimal minutes ang_sec - Degrees, minutes, and decimal seconds
Sets the default number of decimal places (0-13) to which to round newly created dimensions. Unrounded dimensions automatically determine the number of decimal places required to display their stored value
If set to yes, then the Decimal Places command will set the config option default_dec_places in the current session to the chosen number in addition to applying it to the text
Defines the default destination of a GTOL created in the drawing environment. No-Destination is the drawing. Yes-Destination is the top model
Set the default type of ISO tolerance table that will be used when setting ISO/DIN tolerancing standard for a drawing or a model
Set the default placement type for surface finishes in MBD
Sets the largest denominator to be used for fractional dimensions. If the fraction can be reduced, then it converts to the lowest possible denominator (for example, 4/32 converts to 1/8)
Std - Displays fractional dimensions in the standard Creo format. Aisc - Displays fractional dimensions in the American Institute of Steel Construction (AISC) format and displays architectural units in AISC format for feet-inches
If more than zero, sets the margin beyond which dimensions are automatically snapped back onto the screen. For example, a value of .2 lets a dimension be 20% of the window size outside the window. If set to zero, disables snapping of offscreen dimensions
If set to Yes, tolerances for non-angular dimensions will be displayed multiplied by 1000
An alternate format for setting default linear tolerance dimensions. First value sets the number of decimal places. Second value is the actual tolerance. For example, 6 0.000025 sets tolerance to six decimal places. The default tolerance is 0.000025
Specify a range for default tolerances of linear and angular dimensions. These values affect only models created after the tolerance options are specified in the configuration file
Specify a range for default tolerances of linear and angular dimensions. These values affect only models created after the tolerance options are specified in the configuration file
Specify a range for default tolerances of linear and angular dimensions. These values affect only models created after the tolerance options are specified in the configuration file
Specify a range for default tolerances of linear and angular dimensions. These values affect only models created after the tolerance options are specified in the configuration file
Specify a range for default tolerances of linear and angular dimensions. These values affect only models created after the tolerance options are specified in the configuration file
Specify a range for default tolerances of linear and angular dimensions. These values affect only models created after the tolerance options are specified in the configuration file
Maintains the tolerance values of a dimension regardless of the changes you make to the nominal value
Maintains the nominal value of a dimension regardless of the changes that you make to the tolerance values
Yes - Displays a tilde (~) in front of a dimension that is set to display as a fraction and has an actual value that is not rounded to equate exactly to the displayed fractional value (the fraction shows 7/32 but the actual value is .22, not 0.21875)
Controls the minimum angle value under which Creo assumes colinearity of the selected items when creating a driven dimension
Encloses reference dimensions in parentheses. No - Follows reference dimensions with the text "REF"
Sets the default status of the Rounded Dimension Value checkbox for newly created or shown dimensions
Controls whether all newly created dimensions are selected when dimension creation is completed
Tbl_driven_tol_val_edit Y/N* - "Yes" allows users to directly edit the tolerance value of dimensions whose tolerance values are driven by tolerance tables. Editing the tolerance value of a dimension will make the dimension non-table-driven. "No" disallows direct editing of the tolerance values of table driven tolerances
Displays dimensions with or without tolerances
Sets the default tolerance class for ISO-standard models. The system uses the tolerance class in conjunction with the dimension value when retrieving tolerances for General or Broken Edge dimensions
Sets the tolerance standard used when creating the model. Set to ansi
Sets the default directory for user-defined tolerance tables for ISO-standard models. All Holes and Shafts tables overwrite existing tables when loaded. Sets directory for user-defined tolerance tables
Determines if fractional dimensions are displayed in feet-inches, such as 1' 3 1/2" for 15.5 inches. Used in retrieval of pre-Creo solids to set detail setup option, and used at runtime when setup value is 'default'
Yes - use dimensions' nominal values in expressions. No - use current values