Creo Configuration Management Tool
Showing category for Creo
Enter an accuracy value to override the default lower limit. The minimum value for accuracy is 1E-06. Set to .000001 for complex geometry
Yes - Execute Activate command automatically after a window is selected. No - Don't execute Activate command automatically after a window is selected
Yes - Turns on the keyboard bell that rings after each prompt. No - Turns off the keyboard bell. To override this setting use the Environment dialog box on the Tools menu
Specifies the quality of surface triangulation used to obtain initial guess points for clearance and interference calculations
Used with the export option iges_out_mil_d_28000. To support MIL-D-28000, your company name is required input and the system prompts you every time you export through IGES unless you set the company name in your configuration file
The location of the folder to store the saved solver data
The location of the folder to store the temporary solver data
Defines the default absolute part accuracy. A default value of 0.0 creates a new empty part with an accuracy of 0.00039 inches, unless another value is defined. Ensure consistent precision across models (especially important for multi-part designs or complex geometry). Set to .0001
xch - Sets the default type of hatch created in models and drawings to Creo native format (*.xch), pat- Sets it to PAT (*.pat)
Yes - conflict dialogs relevant for Save (regeneration, failure, mass properties etc) appear on checkpoint creation if applicable. No - if possible, conflicts are resolved silently, allowing CP creation
When you use a `Save` command during a Design Exploration session, it does not save the session, it prompts to add a new checkpoint
Set the maximum number of automatically created checkpoints allowed. Additional checkpoints override previous checkpoints. Type a value from 1 to 99. Type 0 to prevent automatic checkpoint creation
Back up all models in session when starting Design Exploration and all models opened and modified during the session. When backup is on, starting a Design Exploration session might take some time
Sets the directory for the Design Exploration session. The default location is in a default system folder. Type a valid file path to change the directory to a user defined one. Data from only one session is stored
Set the default display of the Checkpoint Tree. 'Tree' - Displays all branches in the Checkpoint Tree. 'Timeline' - Displays checkpoints in chronological order (des_exp_display_type)
Open the Checkpoint Properties dialog box when you add a new checkpoint, or turn an automatic checkpoint into a regular one
Determines whether or not annotations are displayed in 3D models. Use this to save memory
Controls the display of the object's full file name (including its object-type suffix and its version number) and file path in the window title and Model Info display. Yes - Displays full file name and file path. No - Displays object name only
Determines whether or not to highlight the selected components during a Model Analysis
Controls the display of a hyperlink screen tip. yes* - Displays a screen tip when you move the pointer over the hyperlink. no - Improves the zoom and pan performance on large drawings. Use this to save memory
Sets a scale factor for enlarging the size of the flip arrow that appears for feature creation direction (default = 1)
Specifies the hatch pattern configuration file to be loaded when Creo is started
Failed annotations are highlighted in the geometry area of 3D models
Yes - Items selected in the model tree are highlighted in the geometry area. Use this to save memory
Setup the default format type for information presentation. Text - information will be output as simple text. HTML - information will be output as html data
Sets default method for presenting information. Both - View information on screen and write information to file. Screen - View information on screen only. File - Write information to file only. Choose - Select method from the INFO OUTPUT menu
Enables Intelligent Fastener. You must restart Creo for the setting to take effect
Defines calculation of Mass properties. Automatic - on each regeneration; report_outdateness_only - outdated mass properties notification is shown; by_request - upon user request; check_upon_save -prompt upon save if mass properties are not calculated. For large assemblies or on-demand analysis, setting this to by_request (instead of automatic) will calculate mass properties only when prompted, improving regeneration speed. Conversely, using automatic ensures up-to-date mass properties at each regeneration (helpful when weight tracking is critical)
Toggles Mathcad analysis automapping of variables
Sets the number of latest contributing features to display in the model tree (2-20, all). Added in Creo 9
The number of mesh triangles which are used to approximate model in collision detection
Sets the number of significant figures displayed as results when using the Measure dialog box from the Info menu
Controls the display of grid balloons
Enables you to specify the prefix to use for negative numbers in the balloon capture of the grid
Controls the number of decimal places displayed in the balloon capture. 0 - Only integers display
Sets the default model grid spacing
Gives the option to display notes as either full text or as label. Can also be toggled with environment option "Display Notes as Names."
Toggles display of the Model Tree. Yes - Displays the Model Tree window along with its model. No - Does not display the Model Tree window
Enable ModelCHECK
Absolute accuracy value will be converted on Set Units -> Interpret operation
Absolute accuracy value will be converted on Set Units -> Convert operation
Absolute accuracy value will be scaled on Scale Model operation
no - Creo does not recalculate the mass properties of legacy parts upon retrieval of a model. yes - Creo recalculates mass properties of legacy parts upon retrieval of a model except for legacy parts with no assigned density
Yes (default) - Creo uses the calculated mass (mass=volume*density) to calculate part mass properties. No - Creo uses the user-defined value of PRO_MP_ALT_MASS if the value of PRO_MP_SOURCE is Geometry and Parameters or Fully Assigned
Yes - Selectable items beneath the pointer are highlighted prior to being selected. No - Selectable items beneath the pointer are not highlighted prior to being selected. Use this to save memory
Default value for "Preselection Highlighting" option in the model tree, layer tree, detail tree and layout tree. When enabled, selectable items are highlighted prior to being selected in the tree. Use this to save memory
Sets the default units for new objects. Set to unit_inch
Sets the default units for mass for new objects. Set to unit_pound
Specifies the default system of units for new models. Which are the units of system in your company
Specify the size in megabytes of the memory buffer to be reserved by Creo for system out of memory condition. You must restart Creo for the change to take effect. Set to a higher value to use more memory
Specifies the directory in which the system stores regen_backup models. (See regen_backup_using_disk.) The primary default is the current directory, but if that directory is read-only, the secondary default is the /tmp directory
Specifies whether or not the system backs up the current model to disk before each regeneration
Yes - Save section surfaces with models. No - Do not save section surfaces with models
All_modes - Select a datum plane by clicking on its visual boundary. Sketcher_only - Select a datum plane by clicking on its tag in modes other than Sketcher. If you use Query frequently, set this option to Sketcher_only
Sets the maximum number of regenerations for each set in the Sensor Data View tool. Defaults to 1, should be increased for models that require multiple regenerations to remove the "need regen" state. Values over 3 are not recommended due to performance
No - Dimension values always appear positive. Negative value creates geometry to opposite side. Yes - Entering negative value for dim displayed as negative creates geometry to same side. Dims for csys and datum point offsets always show neg/pos value
Show id of Creo and Sketcher geometry in query selection bin, collector and tool tip
Determines whether or not the spin center symbol displays. Turning off the on-screen spin center indicator makes the display less cluttered while rotating the model (the spin center can still be toggled or used as needed)
Determines whether or not the application manager starts when Creo is started
Determines whether or not the visualization components are checked for installation upon startup
Specifies the maximum quality of surface triangulation used in surface analyses. Added in Creo 11