Creo Configuration Management Tool
Showing category for Creo
Allow the creation of pre-Pro/ENGINEER 2000i geometry features including ear, neck, lip, slot, flange, shaft, local push, radius dome and section dome
Enables the usage of advanced copy/paste functionality to control degree of dependency on the pasted object
Defines the Cosmetic Thread user interface. Yes - Creates a Cosmetic Thread as a UDF. No - Creates a Cosmetic Thread as a Cosmetic Thread feature
Modify grid space in angular units for handle movement
Allows Creo to automatically switch from add to remove of material for solid extrude and revolve during feature creation
If set to yes, copying a feature group containing an Annotation feature will automatically hide the Annotation Features in the new group
If set to yes, a Sketch feature is automatically hidden after being used as external sketch for a sketch based feature. Automatically hides sketch after using it as reference
Determines the maximum number of edge chains that the Auto-Round algorithm will attempt to round in each Auto-Round member
Modify grid space in centimeter units for handle movement
If set to yes, allow to copy set datum associated with datum features
Sets the default for copy dependency to either full or partial in the Mirror and Paste Special tools
Display Dragger for Edit mode
Controls the default state of geometry preview within a feature tool. Attached/Unattached - Dynamic attached/unattached geometry preview will be enabled. No - Geometry preview will not be enabled
Enable Auto Regeneration for Unified Edit Mode
Presents a notification dialog when the result of a Remove feature creates a surface with a flipped normal, an intersection with non-adjacent geometry or geom check errors. Setting this option to no will not issue the notification
Enables you to add a taper to an extrude feature by displaying the Add taper check box and the taper degree value box on the Extrude tab Options tab. yes - The Add taper check box is displayed. no - The Add taper check box is not displayed
Handles unattached protrusion and cuts, when retrieving pre-Release 15 models. Yes - When a part is retrieved, the system fails an unattached protrusion or cut. No - When a part is retrieved, the system does not fail an unattached protrusion or cut
In feature creation, determines whether or not the Define button is automatically activated when you open the dialog box. Yes - Button is activated automatically. No - You select the button
In feature creation, determines whether or not the system activates the dialog box OK button automatically when the last required element is defined. Yes - Button is activated automatically. No - You select the button
It sets the solid or surface default type for feature creation. The Advanced option sets the default type for Extrude and Revolve to solid, and all others to Surface
Initial value for the "Maintain solution topology" option in created flexible modeling features
Modify grid space in foot units for handle movement
No- Uses hole-table-driven standard hole diameter value. Yes - Allows specifying the drilled hole value instead of the standard value
Specify Hole tool to use external hole parameter (.hol) files
If set to no, and both TAP and TAPERED file types are present in the location given in hole_parameter_file_path, then do not load the system-provided .hol files. Added in Creo 8
Specifies the directory path for a standard screw-size parameters (.hol) file to be loaded from disk. Use the full path name to avoid problems
Modify grid space in inch units for handle movement
Sets the initial state of how the system treats datums and features created at run time
Sets the maximum regeneration time for the dynamic attached preview
Sets the default merge type surface merge operations
Modify grid space in meter units for handle movement
Modify grid space in millimeter units for handle movement
Sets the default directory for the user-defined feature (UDF) library. If not specified, your current working directory is the default. Use the full pathname to avoid problems
Modify grid space in percentage units for handle movement
Yes - The SHOW ERRORS menu appears at the end of feature creation when the feature being created has Geometry Checks
Allow usage of old feature statuses columns in model tree
Sets the default setting to create parameters and note in simple Hole. Added in Creo 10
When set to Yes this option will add a "Show info items" filter to the View panel in the Troubleshooter
If set to yes, a sequential number will be appended to the name of annotation feature in group from Copy and UDF placement
Modify grid space in user defined length units for handle movement